That reflection is interpreted as motion for turning camera recording on.Here is an aerial photo of my property.
Compare to Similar Products (change comparison) Our Analysis and Test Results. Shorter clip lengths and longer retrigger times will make that storage last longer, but you decrease the chance of capturing meaningful footage (recording the moment a burglar looks right at the camera, for example).For the most part, this camera's footage looks quite good. Generally it would eventually yield and treat us to a nice and uninterrupted stream, but this respite usually came after quitting and restarting the app 3 or more times. *For XT2 camera ONLY – at this point you will get an extra screen (shown below) that will ask you to grant the Blink App access to your microphone. After a successful connection, navigate back to the Blink App. 3. Tap to Add a Blink camera . I have tried both 6 and 7 for motion sensitivity and do not want to go higher for false alerts.Should I be expecting better results than this or is this normal?Camera is set to motion setting of 7 and it has 5 bars to wifi extender and 5 bars to sync module.Realize the motion detector does not detect motion. However, we did run into occasional but not infrequent times when the live view window just failed to load. Scroll... How to Use Two-Way Audio. Here is a guide to help use this new feature.... How to Use Customizable Activity Zones with XT2. It started recording the van about the same place as your black car is.see my reply on your other post.Before the updates it used to usually pickup vehicles when on the left side of the bush. Our new Mini and XT2 cameras have two-way audio.
What is odd is that it used to work better when I first got it on release day before all the subsequent updates from Blink. The cam is installed around 9ft up on the SW corner of my house (green circle) The purple square is where I have seen motion detection working on vehicles but not consistently. Setup Cont’d. The orange area is where I almost always get motion detection on people and vehicles.I have XT1 (originals) so I can’t answer on XT2.However, if I turn sensitivity up to 7, it will pick up traffic on both roads at end of driveway. Leave the Blink app and go to Settings>WiFi. However, if you go on vacation for 9 days and something happens on day 1 or 2, there is a chance that footage will have been deleted by the time you get home (depending on your settings and how many more times the motion sensor was triggered in the interim). However, this problem can be rectified by checking in on the camera's live view once every couple days while you're gone. 5. Your Blink XT2 can withstand outdoor use and contact Power adapter designed only for use with Blink with water under certain conditions. What is odd is that it used to work better when I first got it on release day before all the subsequent updates from Blink. Once it's added successfully, tap “Done”. Read guide then tap Ready. While your camera is added, the Blink app will show you some helpful tips for positioning your camera.
However, those drawbacks don't make it less effective as a security camera, just make it less likely you're going to get an amazing, instagram worthy video when a bear decides to do a handstand in your front yard.
Wifi signal is 4-5 bars on camera to router/wifi and camera to sync module.Also it totally missed my vehicle when I got home today as a pulled from the left past the bush and continued on to the section in the middle connecting the 2 driveways.I have an XT2 on the end of my house to watch my drive. To adjust the speaker volume of your XT2, tap on the Settings icon next to the camera's name. The driveway is mostly perpendicular to the camera and it has a very hard time detecting vehicles or people until they are close to the camera. I have a loop driveway like yours and about the same size. However, Blink XT2 is not intended for underwater use and may experience devices. Connect to the Blink-#### network. It’s normal to see “Security Recommendation" or “Connected, no Internet”. We would assume this happens when the wifi network is being taxed, but even if that's the case, we'd much prefer a temporarily lower-quality stream than one that fails multiple times.Additionally, when in the live view mode, the camera stops you every 30 seconds and asks if you want to continue.
5. However, this also means you'll fill up that 2 hours of storage more quickly, and that the older clips will start getting deleted.
4. For instance, no matter your clip length and retrigger settings, if you come home from work and find your trash cans strewn about or something missing, chances are your that footage will still be there when you jump into the app to check, even if you have a longer clip length seslected. Here is a picture from my van pulling into my driveway. Those constant interruptions feel annoying if you're trying to monitor something that is happening in front of the camera, and we wish there were a simple record button instead of only a save/discard option every 30 seconds.These restrictions don't really feel limiting when you're at home. 1. Name and position your camera then tap the snapshot.